Thermoworks HAXO-8 LOGTAG TRANSIT RECORDERS Quick Start Guide Manual do Utilizador descarregar pdf (Página 2)

Signal Sequence Occurrence

LogTag

wake-up

signal

Sequence of four

alternate ashes of

green-red LED’s

• displayed after conguration has been successfully applied to the LogTag

• when a LogTag

is woken up from hibernation state

Not to be mixed up with...

LogTag

start-up

signal

Sequence of sixteen

alternate ashes of

green-red LED’s

• displayed when the LogTag

starts its recording cycle

Mark signal Sequence of ve

simultaneous ashes of

green and red LED’s

• displayed when pressing start/mark button while recording to indicate an inspection

mark in the software

• displayed directly after the start-up signal following a push button start where a

recording delay has been congured. In this instance the start-up signal is repeated

when the actual recording begins

Logging active, no

alert present

Single ash of green

LED every 4 seconds

(approx.)

• indicates LogTag

is recording

• is is not displayed when pre-start is active and the main logging cycle has not

yet started. It is also not displayed when the green LED has been turned o in the

conguration screen

Logging nished,

no alert present

Single ash of green

LED every 8 seconds

(approx.)

• indicates LogTag

has nished recording

• is is not displayed when the green LED has been turned o in the conguration

screen. Will also be displayed when unit has been woken up from hibernation

Alert condition

present

Single ash of red

LED every 4 seconds

• displayed when the LogTag

has detected an alert condition and the Alert LED has

been activated

If an alert is present you cannot determine if the unit is still logging or has n-

ished its log cycle. If the Alert LED has not been activated during conguration,

in essence the visual indicators have been disabled, and the green LED will ash

every 4 or 8 seconds as above.

Communication e green LED will

ash occasionally

• during communication with the interface the green LED will ash occasionally; no

information is conveyed in this

Start button press red LED glows faintly

• is is by design but conveys no information

Table 2: Light Patterns

For a full list of features please see the LogTag® Analyzer User Guide,

which can be accessed through the Help Menu. You can also call up

on-line help information for all windows and dialogue buttons by

pressing the F1 key.

loGtaG indicator leds

e LogTag® recorder itself can give you important status information

by ashing its indicator LEDs in dierent patterns. Both the red ‘Alert’

LED and the green ‘OK’ LED convey information about conguration

and trip parameters, Alert status and give feedback when users interact

with the START/MARK button.

You will nd a summary of the LED patterns with a description about

their meaning in table 2 on the right.

start/MarK Button

Once a LogTag® has been congured, pressing the START/MARK but-

ton has a dierent outcome depending on what

the recorder is doing at the time the button is

pressed.

• If the recorder is congured for a push but-

ton start, pressing this button will activate

the main recording. ere is no need to be

concerned about any lost data if the user

forgets to press this button, as a pre-start

recording feature can be activated, logging

data even before the trip is started.

• Once the LogTag® has been started, pressing

the button will insert an inspection mark in

the data recordings, which is displayed when

viewing the data in the software.

• If congured, Alert Conditions can be reset

when this button is pressed.

custoMi;inG the software

The software allows you to customize many of

the features to your individual requirements.

Not only can you change some of the more

basic options like display language and

temperature units, but also adapt some of the

more advanced parameters for e-mail and FTP

functions, storage folder location, le name and

frequency for automatic software updates.

GettinG the riGht results

When you use the LogTag® units, please take a

moment to consider the application and how

to best approach the monitoring task. Allow the units to be located in

a place with good air movement, make sure HAXO units are not lying

at so water and dust cannot gather around the sensor lter and pro-

vide adequate insulation around access holes for sensors with probes.

certifications

LogTag® has achieved certication with a number of Authorities,

demonstrating the quality and suitability of the LogTag® Recorders for

applications where accuracy and consistency is required. Such certica-

tions have - amongst others- been issued by such organisations as the

FCC, CE, C-TICK, TÜV and the WHO.

fda title 21 cfr 11

Compliance to the FDA requirements is available to users via a special

server utility, available on request, which can log events and be used to

digitally sign data les.

Maintenance

LogTag® recorder products are rugged and need little maintenance,

it does pay however to observe some basic rules when handling the

recorders to maximize their use.

Battery rePlaceMent

Most LogTag® recorder products have a replaceable battery, some of

which may be soldered to the electronics to avoid contact issues that

exist with other branded loggers; for these you will need some soldering

expertise and a battery replacement kit from your distributor. Please

also note that the products do contain a non-rechargeable Lithium Bat-

tery, which must be disposed of in accordance with local regulations.

hiBernation

To prolong the life of your recorder you can hibernate it between trips

via LogTag® Analyzer when it is not being used for extended periods.

Please refer to the User Guide in the section about ‘Hibernation’

caliBration

All LogTag® recorders can be calibrated with spe-

cial utility software, which will be made available

to calibration labs upon request. Re-calibrated

loggers can be identied and traced back to the

calibrating lab thus reducing the risk of fraudu-

lent data tampering.

Basic trouBleshootinG

water inGress

Please carefully observe the IP rating for your unit

and remember that none of the LogTag® products

can be immersed into liquids.

contact cleaninG

Keep the three metal contacts at the back of the

recorder clean and free from tape residue, dirt

or other contaminants, as these usually result in

communications problems. If required, clean

them with a soft pencil eraser, but don’t use abra-

sive materials as you may permanently damage

them.

GettinG helP

If after studying the User Guide you still need

further information, please visit the Support sec-

tion of the LogTag® Recorders website.

thanK you...

...for choosing LogTag® Recorders, we are looking

forward to working with you!



1 2

Quick Start Guide 1

Comentários a estes Manuais

Sem comentários

Thermoworks HAXO-8 LOGTAG TRANSIT RECORDERS Quick Start Guide Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Instrumentos de medida Thermoworks HAXO-8 LOGTAG TRANSIT RECORDERS Quick Start Guide